top of page

Complete cable set. Custom cut to fit this specific model.

 

NOTE: This cable set fits the 2004-2008.5 configuration ONLY. This configuration has four 12v batteries under the seat with a controller/obc cover between them. For newer style cars with the electronics located behind the battery pack, order the 2008.5 and newer style kit.

 

Features include:

  • Fine-stranded welding cable for maximum power conductivity
  • Hydraulic crimped copper terminals
  • Double wall heat-shrink tubing on terminals to keep out debris and corrosion
  • This is a FULL CABLE KIT. It replaces ALL high amperage cables on the entire vehicle. Not just on the batteries.
  • Available with or without OBC compression terminal (explained below)

 

Please order the correct size cables for your application. 2 Gauge Cable sets are rated for up to a 600 amp controller. 4 Gauge cable sets are rated for up to a 400 amp controller

 

Do you need an OBC compression terminal? Maybe, maybe not.  The Onboard computer, or "OBC" was used on all 48 volt Club Car vehicles from 1995 until 2014. If you're still using your Powerdrive, Powerdrive 2, Powerdrive 3, or IQ Plus charger, your cart has an OBC.  These chargers will not function correctly without an OBC. The OBC is the brain behind these chargers.  A common modification to these vehicles is to delete or "bypass" the OBC. The reason for this is to allow you to be able to use a more advanced charger such as the Lester Summit 2, FSIP Charge Plus, or the MODZ Max.  There is a small hole in your original OBC in which the main negative cable must pass through in order for the OBC to accurately monitor battery voltage information and charge data. When installing a custom cable set you will be required to cut the original cable that runs through this hole and replace it with a new negative cable. The copper terminal is far too large to pass through this hole. This is where the OBC compression terminal comes into play. If you are using the OBC for charging, you will need to select "YES" from this drop-down menu. We will send you a compression terminal along with one cable of your cable set that is unfinished on one end.  You will then lubricate this cable and pull it through the hole in the OBC. DO NOT DRILL THIS HOLE. 4 AWG and 2 AWG wires will fit through this hole. If you enlarge the hole, the OBC will be ruined.  Once you pull the wire through you can cut back the insulation and place the compression terminal anchor onto the copper wire. Once it's in place you can thread the compression terminal onto the anchor using two wrenches.  Once it's tightened fully, you will have a nice tight secure connection and a finished cable to complete your installation.  A piece of heat-shrink tubing comes with the compression terminal to finish the job and make it look nice.  Please reach out if you have any further questions.

 

If you are unsure of what drive system you have, please call or email us prior to ordering.

Complete Cable Set for 04-08.5 48V Club Car Precedent with four 12V Batteries

$119.84Price

    Please note that item availability has been getting better every day since the COVID-19 Pandemic of 2020. Our online products are typically in stock and available if they are marked "IN STOCK" in our online store. The only reason an item would be marked "OUT OF STOCK" is if we know for a fact that there is a long-term back-order situation on that particular item and we do not know when we will be receiving it. Please be aware that we sell these items online as well as locally, so it's difficult to maintain accurate available quantity on the online store at all times but we try our best to keep up. Typically if we do not have an item in stock, it can be received locally from our vendors in 1-2 days before it ships to you. Certain items may also be shipped directly from the vendors to you without delaying your order arrival at all. If you're concerned about the stock status of an item we strongly suggest that you contact us prior to ordering to ensure that the items are available for immediate shipment. If you place an order for an item that is not in stock you will be notified via email within 24 hours and an estimated ship date (shown on your emailed invoice) will be provided to you at that time.  Please make sure the email address associated with your payment matches the email address that you currently use. Lots of our customers have old email addresses attached to their payment accounts and do not receive emails from us because they forget to check their old email account. If you place an order and choose to cancel at anytime, no problem. Be aware that cancelled orders in back-order status will be fully refunded minus the non-refundable 3.5% PayPal or Credit Card processing fee. This is why we strongly recommend that you ask about availability status PRIOR to ordering by texting or emailing us. Please provide the SKU number of the item in your message. A text message is fine and will typically be answered in just a few minutes. This is explained in further detail on our main page, or by clicking HERE.

    CONTACT US:

    Text: 706-431-3917

    Email: info@revolutiongolfcars.com

    bottom of page